Open Access Open Access  Restricted Access Subscription Access

Structural and Vibration analysis of Automobile Engine Shafts

Venkata Sanyasi Seshendra Kumar Karri

Abstract


In the present work, dynamic analysis is carried out on an engine shaft for a single cylinder four stroke engine. The shafts are modeled using finite element analysis and the intensity of stress magnitude is determined.  It is shown in the paper that the stress variation is high at some critical points. The dynamic analysis is carried out analytically at different engine speeds and is verified by simulation software.  As a result, the critical engine speed and critical region on the shafts are obtained.


Full Text:

PDF

References


C.M.Balamurugan.,R.Krishnaraj.,Dr.M.Sakthive.l,K.Kanthave.l,DeepanMarudachalamM.G.,R.Palani.,2011“ComputerAided Modeling and Optimization of Crankshaft,’’ International Journal of Scientific & Engineering Research Volume 2, Issue 8 ISSN 2229-5518

Yu Ding and Xiaobo Li.,2011, “ Crankshaft Strength Analysis of a Diesel Engine Using Finite Element Method,” Asia-Pacific Power and Energy Engineering Conference

JianMeng., Yongqi Liu., Ruixiang Liu.,2011,“FiniteElement Analysis of 4-Cylinder Diesel Crankshaft, ” I.J.Image, Graphics and Signal Processing, 5, 22-29

MENG Jian., LIU Yong-qi., LIU Rui-xiang., and ZHENGBin.,2011,“Intension Analysis of 3-D Finite Element Analysis on 380 diesel crankshaft,” International Conference on Computational and Information Sciences

Yu Gongzh.i, Yu Hongliang.,DuanShulin., 2011,“Crankshaft Dynamic Strength Analysis for Marine DieselEngine,” Third International Conference on Measuring Technology and Mechatronics Automation.

GuYingkui, Zhou Zhibo.,2011,“Strength Analysis of Diesel Engine Crankshaft Based on PRO/E and ANSYS,” Third International Conference on Measuring Technology and Mechatronics Automation

Xiaorong Zhou., GanweiCai., Zhuan Zhang. Zhongqing Cheng., 2009, “Analysis on Dynamic Characteristics ofInternal Combustion Engine Crankshaft System,” International Conference on Measuring Technology and Mechatronics Automation.

Farzin H. Montazersadgh and Ali Fatemi., 2007,“DynamicLoad and Stress Analysis of a Crankshaft,” SAE Technical Paper No. 010258, Society of Automotive Engineers

JonathanWilliams,FarzinMontazersadgh,andAlifatemi.,2007,“FatiguePerformance Comparison And Life Prediction of Forged Steel And Ductile Cast Iron Crankshafts,” Published in Proceeding of the 27th Forging Industry Technical Conference in Ft.Worth,Texas

Shenoy, P. S. and Fatemi, A., 2006, “Dynamic analysis of loads and stresses in connecting rods,” IMech E, Journal of Mechanical Engineering Science, Vol. 220, No. 5, pp. 615-624

Zoroufi, M. and Fatemi, A.,2005, "A Literature Review on Durability Evaluation of Crankshafts Including Comparisons of Competing Manufacturing Processes and Cost Analysis", 26th Forging Industry Technical Conference, Chicago,

Prakash, V., Aprameyan, K., and Shrinivasa, U.,1998, “AnFEM Based Approach to Crankshaft Dynamics and Life Estimation,” SAE Technical Paper No. 980565, Society of Automotive Engineers

Payar, E., Kainz, A., and Fiedler, G. A., 1995, “Fatigue Analysis of Crankshafts Using Nonlinear Transient Simulation Techniques,” SAE Technical Paper No. 9.


Refbacks

  • There are currently no refbacks.